ADTRAN OPTI-3 CPE User Manual download pdf

JOBAID

61184002L4-22B

0401

OPTI-3

CONTROLLER

CLEI: SOI4JN4D_ _

OPTI-3

ENABLE

TESTAPS ACO

1184002L4

CRAFT

1550nm

STATUS

OPTICS

DS3-1

ACO

DS3-2

DS3-3

DESCRIPTION

The Total Access

OPTI-3 Controller Module (OCM) provides an OC-3 interface to the network and three ADD/DROP DS3

interfaces to the Loop. The OCM can be configured for a point-to-point configuration or subtended from 3rd party SONET

equipment. The OCM operates in terminal mode only. The compact design mounts in either a rackmount or wallmount

chassis, requiring less space and provides optional redundancy. It can automatically switch to the offline unit in the event of

optical signal failure or degradation. The modules are fully hot-swappable.

Compliant with SONET standards, the OCM functions as a terminal multiplexer. It supports 1+1 OC-3 equipment and facility

protection, 1:1 OC-3 equipment protection (system provisioned for optical Ycable), 1:1 DS3 facility protection, and detects

standard optical related alarm conditions. The OCM can be configured to operate redundantly with optional protection of

the optics components. It can be upgraded online from un-protected to protected and operating software can be upgraded

remotely in Back-to-Back configurations.

The OCM is easily managed with TL1 commands over the Data Communications Channel (DCC) or via Command Line

Interface (CLI) through the local craft interface. Additional features include remote alarm transport via DCC and alarm

reporting to legacy alarm systems.

FIRMWARE RELEASE

This job aid relates to OPTI-3 System Release 1.3 (Dseries). The menus and functionality are an extension of the prior system

release (OPTI-3 System Release 1.2 - Cseries). The latest software is not compatible with System Release 1.1 (Bseries).

INSTALLATION

The Total Access OPTI-3 can be installed in either a Rackmount Chassis (RMC), P/N 1184003L1, or a Wallmount Chassis

(WMC), P/N 1184001L1. The RMC provides two OCM slots, side by side, with slot A on the left and slot B on the right. (See

Figure below.) The WMC provides two OCM slots, positioned vertically with slot A below slot B. Ensure the appropriate

chassis is installed before proceeding with the OCM installation.

Carefully insert the OCM halfway into the selected slot. Route the fiber cables through the notch on the OCM front panel and

approximately 4 inches past the SC receptacles (to create slack). Gently but firmly push the OCM all the way into the slot,

being careful not to pinch the fibers between the front panel and the shelf. Push the latch/ejector tab toward the front panel

to lock it into place.

WARNING: Once fully inserted into the chassis, the module will be powered (provided power is connected to the chassis).

When the OCM powers up, it performs a self-test. The front panel LEDs illuminate for approximately 8 seconds. The self-test

is complete once the STATUS LED illuminates green.

If installing a redundant system, repeat the preceding procedure for slot B. If not installing a second OCM, a blank faceplate

(P/N 1184005L1) must cover the empty slot.

C A U T I O N

SUBJECT TO ELECTROSTATIC DAMAGE

OR DECREASE IN RELIABILITY.

HANDLING PRECAUTIONS REQUIRED.

■ For a complete Installation and Maintenance Practice (P/N 61184002L4-5): 877-457-5007, Faxback Document 964. Please have your fax number ready. ■

LED STATUS

STATUS ● Green In-Service

● Yellow Unit is Out-of-Service – Unassigned

✷ Flashing Yellow Unit is Out-of-Service – Maintenance or is ONLINE and inhibited

from switching

● Red Unit has an equipment failure

OPTICS ● Green Normal Operation

● Yellow Soft failure (e.g. RDI)

✷ Flashing Yellow Unit in Test (e.g. Loopback)

● Red LOS, LOL, and other hard alarms on optical interface

✷ Flashing Red Unit in Test (e.g. Loopback) with an alarm present on the Optical

Interface

DS3-1 – DS3-3 ● Green Unit is ONLINE (DS3 TX ON)

● Yellow Soft failure (e.g. RDI)

✷ Flashing Yellow Unit in Test (e.g. Loopback)

● Red LOS, LOL, and other hard alarms on DS3 interface

✷ Flashing Red Unit in Test (e.g. Loopback) with an alarm present on the DS3

Interface

ACO ● Yellow When displayed on the OCM at the CO, indicates acknowledged

active alarms at the RT

✷ Flashing Yellow When displayed on the OCM at the CO, indicates an unacknowl-

edged active alarms at the RT

● Red Acknowledged alarms active on the shelf

✷ Flashing Red Unacknowledged alarms active on the shelf

APS PUSHBUTTON

■ When depressed simultaneously with the TEST/ENABLE switch on the Offline unit, a switch is forced

between the two OCMs.

■ When depressed with the TEST/ENABLE switch on the Online unit, it toggles LOCKOUT status.

TEST/ENABLE BUTTON

■ When depressed alone, tests all unit LEDs (multicolor LEDs appear YELLOW).

■ When depressed simultaneously with the APS switch on the Offline unit, a switch is forced between

the two OCMs.

ACO BUTTON

■ When depressed after an audible alarm is sounded, silences the alarm.

■ When depressed after any other alarm is triggered, acknowledges alarm.

CRAFT INTERFACE

■ Provides menu access via RS-232 (Craft) port on the front panel.

■ Connects to VT100 compatible terminal using a DB-9 serial cable.

■ Requires setting VT100 terminal emulation (to 9600, 19200, 38400, 57600, or 115200 bps), 8 Data Bits,

No Parity, 1 Stop Bit, and No Flow Control. (The baud rate default is 9600 bps, which can be

modified through the VT100 menu system.

■ Provides access to both OCMs installed in the chassis with connection to either OCM craft port.

NOTE: The OPTI-3 is an LR (long reach) optical product. When interfacing with IR (intermediate

reach) 3rd party equipment, the optical receive signal may need to be padded to avoid

overloading the optical receive signal. The receive signal level should be within

−

8 dbm to

−

28 dbm for IR equipment.

WARRANTY

ADTRAN will replace or repair this product within the warranty period if it does not meet its published

specifications or fails while in service. Warranty information can be found at www.adtran.com/warranty.

U.S. and Canada customer Faxback: 877-457-5007, Document 414.

#61184002L4-22B#

TOTAL ACCESS OPTI-3 CONTROLLER MODULE

1550 NM

1 2

CONTROLLER 1

Summary of Contents

Page 1 - CONTROLLER

JOBAID61184002L4-22B0401OPTI-3 CONTROLLER CLEI: SOI4JN4D_ _OPTI-3ENABLETESTAPS ACO1184002L4CRAFT1550nmSTATUSOPTICSDS3-1ACODS3-2DS3-3DESCRIPTIONThe Tot

Page 2

PRICING AND AVAILABILITY 800.827.0807TECHNICAL SUPPORT 800.726.8663RETURN FOR REPAIR 256.963.8722www.adtran.com61184002L4-22BTOTAL ACCESS OPTI-3

Comments to this Manuals

No comments

ADTRAN OPTI-3 CPE User Manual

Browse online or download User Manual for Network switches ADTRAN OPTI-3 CPE. ADTRAN OPTI-3 CPE User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Network switches ADTRAN OPTI-3 CPE