ADTRAN 1442701PG2 Datasheet download pdf

jobAid

DESCRIPTION

TheOC‐3SmallForm‐FactorPluggableCWDM,1491nm(SFP

OC3)plugsintoADTRANOC‐3equipmentdesignedtoaccept

SmallForm‐FactorPluggables(SFPs).

Installedintoanappropriatehostunit,theSFPOC3providesan

OC‐3CWDMinterfacetothesupportingsystem.

NOTE

Toensurecompatibility,refertothedocumentationprovi ded

withthehostmodule.

ThefollowingfeaturesaresupportedontheSFPOC3:

♦ SONETOC‐3compatible(155.52Mb/s)1491nm,

longreach,single‐mode,2‐fiberoperation

♦ 80kmmaximumopticalspan

CAUTION

Duetocompliancecertificationrequirements,use on lySFPs

suppliedbyADTRANwiththehostmodule.ADTRANcannot

certifysystemintegritywithotherSFPs.

SPECIFICATIONS

♦ OpticalSpecifications:

◊ Opticaltransmitlevel:0dBmto–5dBm

◊ Opticalreceivelevel:–10dBmto–34dBm

◊ Powerpenalty:–1dB

◊ Opticalbudget:28(±1)dBm

◊ Minimumspanattenuation:10dB

◊ Opticalconnectors:LC

♦ ExtendedEnvironmentalSupport:

◊ Operationaltemperaturerange:–40°Cto+65°C

◊ Storagetemperaturerange:–40°Cto+85°C

◊ Relativehumidityto95%,noncondensing

OC-3 Small Form-Factor Pluggable

CWDM, 1491 nm

INSTALLATION

ToinstalltheSFPOC3intoanappropriatemodule,completethe

followingsteps:

1. InspecttheSFPOC3.Ifdamaged,fileaclaimwiththecar‐

rierandthencontactADTRANCustomerSupport.

CAUTION

DonotremovetheprotectiveendcapfromtheSFPuntilthefiber

opticcableisreadytobeconnected.

2. InserttheSFPOC3intotheSFPcageonthemodule.Ensure

thatthemanufacturer’slabelontheSFPisfacingupwardfor

correctinstallation.

3. SlidetheSFPOC3allthewayintothereceptacleuntilthere

isanaudible“click”.

NOTE

ThelatchontheSFPisusedtoremovetheSFPfromthecageon

thecircuitcard.

PROVISIONING

The SFPOC3 is not directly provisionable. To provision the

SFPOC3, access the menu system of the host module. Refer

to the “Provisioning” section of the Job Aid or Installation

and Maintenance Guide (I&M) provided with the host

module for provisioning details.

SAFETY AND REGULATORY COMPLIANCE

CAUTION

ElectrostaticDi schar ge(ESD)candamageelectronicmodules.

Whenhandlingmodules,wearanantistaticdischargewriststrap

topreventdamagetoelectroniccom pon ents .Placemodulesin

antistaticpackingmaterialwhentranspo rtingorstoring.When

wor kin g on modules, always placethem on an approved

antistaticmatthatiselectricallygrounded.

TheSFPOC3isNRTLListedtotheapplicableULstandards.The

SFPOC3meetsorexceedsalltheapplicablerequirementsof

NEBS,TelcordiaGR‐63‐CORE,GR‐1089‐CORE,andETSIEN

300368.

TheSFPOC3isintendedfordeploymentinCentralOfficetype

facilities,EEEs,EECs,andlocationswheretheNECapplies(for

example,CustomerPremises).TheSFPOC3istobeinstalledin

ADTRANproductsinRestrictedAccessLocationsonly,and

installedbytrainedservicepersonnel.

ThisdevicecomplieswithPart15oftheFCCrules.Operationis

subjecttothefollowingtwo

conditions:

1. Thisdevicemaynotcauseharmfulinterference

CLEI: SITRAAGA_ _

Product P/N: 1442701PG2

Issue Date: November 2010

Document P/N: 61442701PG2-22C

1 2

CWDM, 1491 nm 1
C A U T I O N 2

Summary of Contents

Page 1 - CWDM, 1491 nm

jobAidDESCRIPTIONTheOC‐3SmallForm‐FactorPluggableCWDM,1491nm(SFPOC3)plugsintoADTRANOC‐3equipmentdesignedtoacceptSmallForm‐FactorP

Page 2 - C A U T I O N

C A U T I O N C A U T I O N ! SUBJECT TO ELECTROSTATIC DAMAGEOR DECREASE IN RELIABILITY.HANDLING PRECAUTIONS REQUIRED.Warranty: ADTRAN will replace or

Comments to this Manuals

No comments

ADTRAN 1442701PG2 Datasheet

Browse online or download Datasheet for Network transceiver modules ADTRAN 1442701PG2. Adtran OC-3 CWDM SFP 1491nm User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Network transceiver modules ADTRAN 1442701PG2